\r\n I know this is outdated information for many people, but it`s here and it should be kept up to date or there is not a lot of point in this post! Anyway... \r\n \r\nIF YOU ARE ON FIRMWARE 3.56 - 4.00 LEAVE THIS PAGE NOW!!! \r\n \r\nRight, if you have purchased an E3 card reader in order to downgrade or enter service mode, then this is how it is done... \r\n \r\nYou need some files that are either available from my links below or from the E3 site in China. \r\n \r\nIMPORTANT: \r\n \r\nYOU CAN ONLY DOWNGRADE FROM 3.55 DOWNWARDS USING THIS METHOD AT THIS TIME. IT WILL *NOT* WORK ON 3.56+ FIRMWARES. IF YOU ENTER SERVICE MODE, YOU WILL BE LOCKED IN IT FOR GOOD AS THERE IS NO UPDATED "FILE 2" LV2DIAG.SELF AT THIS TIME. IF YOU ARE ON 3.56+ - LATEST FIRMWARE, LEAVE THIS PAGE NOW!!! \r\n \r\nEARLY FAT PS3 40GB/60GB/80GB MODELS WITH A 256MB NAND WILL HAVE THEIR BLURAY PLAYBACK DISABLED IF YOU DO THIS, UNLESS YOU BACK UP YOUR DEV_FLASH FOLDERS BEFOREHAND!!! SEE ELSEWHERE ON HOW TO DO THIS. IF YOU HAVE A LATER FAT MODEL OR A SLIM MODEL THEN YOU ARE SAFE. DO SOME RESEARCH TO AVOID HASSLE LATER ON. \r\n \r\nIF YOUR BLURAY DRIVE IS MISSING (THE LOGIC BOARD ACTUALLY) THEN YOU WILL NOT BE ABLE TO INSTALL ANY FIRMWARE TO YOUR PS3 UNLESS YOU MAKE A SPECIAL PS3UPDAT.PUP USING PS3MFW BUILDER OR ANOTHER PUP THAT SUPPORTS BLURAY-LESS INSTALLATION. I BELIEVE THERE IS ALSO A SCRIPT THAT YOU CAN RUN TO BYPASS THE BLURAY DRIVE CHECK \r\n \r\nWe need: \r\n \r\nE3 downgrade firmware : ... First link at bottom of post \r\nhttp://www.multiupload.com/2ER2QKNE4M \r\n \r\nLV2diag.SELF file 1 : ... Link at bottom of post *OPTIONAL - USE ONLY IF DOWNGRADING \r\n \r\nLV2diag.SELF file 2 : ... Link at bottom of post \r\n \r\nDirections are as follows... \r\n \r\n1) Eject discs if there is one in the console, then completely disconnect power from PS3 - On FATS flick the switch on the back, on SLIMs disconnect power lead for 5-10 seconds, then apply power so the red light comes on, but DO NOT TURN ON YET! \r\n \r\n2) Insert your E3 card reader into your PC. Ensure there is no MicroSD card slotted inside it. After a few moments, you will see 2 new drives in "My Computer". One is a standard 3.97mb drive and another called "Upgrader" which is 126kb in size (The card reader won`t light up or anything). \r\n \r\n-In the E3 downgrade firmware folder you have downloaded (and unzipped) there is a file called "e3downgrade 12.03.bin" and we need to drag this bin file to the Upgrader drive. \r\n \r\n-IMPORTANT : When you drag it over, there will be a red LED that will flash for a second or two, then it will turn blue. Once it has turned blue, this confirms that we have just installed the downgrade firmware to the E3 card reader. If you do not see a blue light, you have done something wrong. Try again until you get the blue light. We can now remove the E3 card reader. \r\n \r\n3) Now insert the card reader into your PS3 (Use the far right USB port as you look at the machine.) \r\n \r\n4) Press POWER then within 2 or 3 seconds press EJECT. This will start the process. After a few seconds, the E3 card reader light will turn blue and the PS3 will switch off. If it doesn`t turn blue, then try again but REMEMBER TO UNPLUG POWER FROM YOUR PS3 EVERY TIME YOU TRY. IT WILL NOT WORK IF PS3 HAS ALREADY BOOTED. YOU NEED TO DISCONNECT THE POWER CABLE OR SWITCH THE SWITCH AT THE BACK \r\n \r\n5) Once the PS3 has powered off, you can now remove your E3 card reader. Now turn your PS3 on and there will be a red box in the bottom corner of the screen saying you are in factory/service mode! \r\n \r\n6) Now, to downgrade, you can put your choice of PS3UPDAT.PUP onto any empty dongle and put the file 1 (LV2DIAG.SELF) on there too. These two files should be in the root of the USB dongle. Power on your PS3 and it will start the downgrade process. This is covered in greater detail elsewhere. To downgrade from 3.55 to 3.41 you will need the modified 3.41 (3.56 spoof) pup, otherwise the standard modified 3.41 will be fine. REMEMBER IF DOWNGRADING, YOUR HARD DRIVE WILL BE COMPLETELY WIPED!!! \r\n \r\n7) To get out of service mode, switch PS3 off and put the file 2 (LV2DIAG.SELF) onto an empty dongle. \r\n \r\n8) Put the dongle in PS3 and turn on. After a few seconds, your PS3 will power off by itself and you will back into retail mode. \r\n \r\nIf I have missed anything out, please let me know! \r\n \r\nBTW: If I`m not supposed to put the links on I do apologise and feel free to delete this if need be. It has only just occurred to me. \r\n \r\nMatty \r\n \r\ne3downgrade 12.03.zip \r\nLv2diag.self FILE 1 - 3.41.zip \r\nLv2diag.self FILE 2 - 3.41.zip \r\nFILE1 Downgrade 3.55.zip \r\nFILE2 Downgrade 3.55.zip\r\n
\r\n
\r\n\r\n \r\n
\r\n
\r\n \r\n
\r\n \r\n \r\n
\r\n \r\n Last edited by pikeytrog; 01-20-2012 at 01:19 PM.\r\n \r\n \r\n
\r\n I am currently on 3.41 modified pup firmware that I downgraded from stock 3.50 firmware with E3 cardreader. I want to go to a custom firmware. According to minverchck, my console can go down to 3.40. \r\n \r\nSince I used modified pup to downgrade my slim, I must downgrade to 3.40 before I can go to custom firmware (3.41 or 3.55). Do I use the same lv2diag.self files 1 and 2 to downgrade and leave service mode as I used when I went from 3.50 to 3.41 mod? \r\n \r\nAlso, above steps 5 & 6 each say turn on ps3. Obviously, in between it must be turned off. This is the time it is just turned off with the controller (and not unplugged) if I remember correctly.\r\n
\r\n
\r\n\r\n \r\n
\r\n
\r\n \r\n
\r\n \r\n \r\n
\r\n \r\n Last edited by JLM; 09-06-2011 at 04:36 PM.\r\n \r\n \r\n
In A Console Scene Full of Trolls, Retards, Bedwetters, Wieners, Masturbators, Manginas and Scumbags
\r\n \r\n
Posts
3,592
\r\n \r\n
Total Thanks Given
12,364
\r\n
Total Thanks Received
4,523
\r\n
Total Thanked Posts
2,192
\r\n \r\n
\r\n \r\n \r\n
\r\n \r\n
\r\n \r\n
\r\n
\r\n
\r\n \r\n \r\n\r\n\r\n \r\n \r\n
\r\n
\r\n
\r\n
\r\n
\r\n
\r\n \r\n \r\n
\r\n Originally Posted by JLM\r\n \r\n
\r\n
I am currently on 3.41 modified pup firmware that I downgraded from stock 3.50 firmware with E3 cardreader. I want to go to a custom firmware. According to minverchck, my console can go down to 3.40. \n \nSince I used modified pup to downgrade my slim, I must downgrade to 3.40 before I can go to custom firmware (3.41 or 3.55). Do I use the same lv2diag.self files 1 and 2 to downgrade and leave service mode as I used when I went from 3.50 to 3.41 mod? \n \nAlso, above steps 5 & 6 each say turn on ps3. Obviously, in between it must be turned off. This is the time it is just turned off with the controller (and not unplugged) if I remember correctly.
\r\n \r\n
\r\n
\r\n
Based on pikeytrog\'s post (I DIDN\'T read this when you\'ve sent me a PM regarding this - EPIC FACEPALM), I assume you use the same lv2diag.self files as apparently "it only works from 3.55 DOWNWARDS" so I assume that it is universal from 3.55 and below - feel free to correct me if I am wrong. \n \nHave a look at the following links for more info: \n \nhttp://www.ps3hax.net/showthread.php?t=16529 \n \nhttp://www.sudburymods.com/psdowngrade.html \n \n \nAccording to DCEmu Reviews \n \nHow to downgrade firmware 3.42/3.50 (NOT v3.55) to firmware 3.41 with E3 Card Reader : \n \n1. Download and extract "e3downgrade_12.03.rar (Download URL: http://www.mediafire.com/?1yoc2rvg7kg7yff)" to your computer \n2. Insert E3 Card Reader into the USB port of your computer. \n3. On your file browser, open "E3Upgrader" \n4. Drag and drop .bin file from "e3downgrade_12.03.rar" into "E3Upgrader" \n5. Red LED will flash. When you see the blue LED, that means the upgrade is successful and complete. \n6. Remove E3 Card Reader from computer \n7. Insert E3 Card Reader device that has been reprogrammed as downgrader into your console \n8. Turn on the console using the same boot method as all other jailbreaks: Press power then immediately press eject. Your console will turn on and E3 Card Reader will light up red LED followed by blue LED \n9. Turn off system via menu \n10. Remove E3 Card Reader dongle and turn on console to make sure you are in Factory Service Mode. You will see a huge red box on the screen saying Factory Service Mode. \n11. Load any blank FAT32 USB flash drive device with 2 files in the root directory: \n \n - Modified 3.41 PUP \n - Lv2Diag.self (File 1) \n \n12. These must be the only files on the USB key and must be placed in the main (root) directory. \n13. Insert flash drive into the last USB port to the right — the first USB port in from the right side if you’re facing the console. Turn the PS3 on and you will see black screen but the PS3 HDD light will flash. \n14. The process takes 3-4 minutes for the system to install the old firmware. Towards the end, the power button on the console will start flashing green and then your console will power off. \n15. Remove the flash drive and turn on the console, you will still be in Factory Service Mode. Please verify you have downgraded successfully to version 3.41 by going to "System Information". \n16. (Optional) - If you wish to downgrade to any older firmware you can follow step 4, 5, 6 using any regular firmware PUP. (You do not need to use modified custom firmware now that you are on 3.41). \n17. Insert USB flash drive back into your PC and delete the PUP and Lv2Diag.self file (File 1) and copy the other Lv2Diag.self (File 2) to the root of the flash drive. \n18. Insert USB flash drive back into the same USB port on the PS3 and power on your PS3. After 10 seconds it will power off. \n19. Remove USB flash drive and turn on your console again. You will be out of factory service mode and back in retail mode with your chosen firmware version installed. You will need to go through setting up settings configuration. \n \nTo go back to E3 Card Reader jailbreak device, just drag back the normal .bin files.\r\n
\r\n
\r\n\r\n \r\n
\r\n
\r\n \r\n
\r\n \r\n \r\n
\r\n \r\n Last edited by gDrive; 09-06-2011 at 09:48 PM.\r\n \r\n \r\n
\r\n \r\n \r\n \r\n \r\n \r\n
\r\n
\r\n
\r\n \r\n \r\n
\r\n Originally Posted by deank\r\n \r\n
\r\n
And to the idiots who laugh and compare other BUMs with mM saying mM is 150MB and others are 2MB - Fuck you.
\r\n \r\n
\r\n
\r\n
\r\n
\r\n
\r\n \r\n \r\n
\r\n Originally Posted by TomatOsaUce\r\n \r\n
\r\n
That\'s coz you masturbate too much over Asian ladies!!
\r\n \r\n
\r\n
\r\n
\r\n
\r\n
\r\n \r\n \r\n
\r\n Originally Posted by dangwoot\r\n \r\n
\r\n
I will tell you this you little bastard, I wasn\'t being "Sarcastic" - I\'m as serious as a heart attack, and you\'re lucky I didn\'t see your reply or you\'d be gone for good you little shit.
\r\n \r\n
\r\n
\r\n
\r\n
\r\n
\r\n \r\n \r\n
\r\n Originally Posted by deank\r\n \r\n
\r\n
He can hardly code a microwave oven to pop some popcorns to fill his fat belly ass
\r\n Thanks for posting this. I have a bunch of similar instructions, but they just say 3.50. I knew the files for downgrading 3.55 were firmware specific, just wanted to double check that the 3.50 weren\'t. Anyway, it worked fine and I\'m now on 3.40 ofw. Thanks.\r\n
In A Console Scene Full of Trolls, Retards, Bedwetters, Wieners, Masturbators, Manginas and Scumbags
\r\n \r\n
Posts
3,592
\r\n \r\n
Total Thanks Given
12,364
\r\n
Total Thanks Received
4,523
\r\n
Total Thanked Posts
2,192
\r\n \r\n
\r\n \r\n \r\n
\r\n \r\n
\r\n \r\n
\r\n
\r\n
\r\n \r\n \r\n\r\n\r\n \r\n \r\n
\r\n
\r\n
\r\n
\r\n
\r\n
\r\n \r\n \r\n
\r\n Originally Posted by JLM\r\n \r\n
\r\n
Thanks for posting this. I have a bunch of similar instructions, but they just say 3.50. I knew the files for downgrading 3.55 were firmware specific, just wanted to double check that the 3.50 weren\'t. Anyway, it worked fine and I\'m now on 3.40 ofw. Thanks.
\r\n \r\n
\r\n
\r\n
You\'re welcome JLM! \n \nIf you have any more problems, give us a shout, okay?\r\n
\r\n
\r\n\r\n \r\n
\r\n
\r\n \r\n
\r\n \r\n \r\n \r\n \r\n
\r\n
\r\n
\r\n \r\n \r\n
\r\n Originally Posted by deank\r\n \r\n
\r\n
And to the idiots who laugh and compare other BUMs with mM saying mM is 150MB and others are 2MB - Fuck you.
\r\n \r\n
\r\n
\r\n
\r\n
\r\n
\r\n \r\n \r\n
\r\n Originally Posted by TomatOsaUce\r\n \r\n
\r\n
That\'s coz you masturbate too much over Asian ladies!!
\r\n \r\n
\r\n
\r\n
\r\n
\r\n
\r\n \r\n \r\n
\r\n Originally Posted by dangwoot\r\n \r\n
\r\n
I will tell you this you little bastard, I wasn\'t being "Sarcastic" - I\'m as serious as a heart attack, and you\'re lucky I didn\'t see your reply or you\'d be gone for good you little shit.
\r\n \r\n
\r\n
\r\n
\r\n
\r\n
\r\n \r\n \r\n
\r\n Originally Posted by deank\r\n \r\n
\r\n
He can hardly code a microwave oven to pop some popcorns to fill his fat belly ass
I know this is outdated information for many people, but it`s here and it should be kept up to date or there is not a lot of point in this post! Anyway... \r\n \r\nIF YOU ARE ON FIRMWARE 3.56 - 4.00 LEAVE THIS PAGE NOW!!! \r\n \r\n \r\nIMPORTANT: \r\n \r\nYOU CAN ONLY DOWNGRADE FROM 3.55 DOWNWARDS USING THIS METHOD AT THIS TIME. IT WILL *NOT* WORK ON 3.56+ FIRMWARES. IF YOU ENTER SERVICE MODE, YOU WILL BE LOCKED IN IT FOR GOOD AS THERE IS NO UPDATED "FILE 2" LV2DIAG.SELF AT THIS TIME. IF YOU ARE ON 3.56+ - LATEST FIRMWARE, LEAVE THIS PAGE NOW!!! \r\n \r\n
\r\n \r\n
\r\n
\r\n
\r\nthere is something that i am missing in this guide,why i should worry about being locked with service mode as lv2diag.self file2 on the flash drive wont work with 3.56 if i will have to insert it after my ps3 have already downgraded to 3.55 or 3.41 firmwares that work fine with with that file?\r\n
there is something that i am missing in this guide,why i should worry about being locked with service mode as lv2diag.self file2 on the flash drive wont work with 3.56 if i will have to insert it after my ps3 have already downgraded to 3.55 or 3.41 firmwares that work fine with with that file?
\r\n \r\n
\r\n
\r\n
\nIf you are on 3.56+ and you try this and it happens to take you to sevice mode, you won\'t be able to get out with the lvl2diag.self even if you happen to be able to downgrade..\r\n
\r\n thats because the files arent signed to run on 3.56+. To get out of service mode, you need to downgrade to 3.55. If you cannot downgrade to 3.55 your shit out of luck, until some figures out the values to modify on the nor flash to enable/disable service mode via hex edit. \n \nIf i have time, i may dump my flash on my cechh02 before and after service mode, and compare the files, then see if changing the vaules to the ones shown in my original nor to see if it get me out, IT SHOULD. \n \nThen maybe see if others stuck on 3.56 with FSM want to try change these values to see if it\'l help them (unsure it it will be different on slims and phats.\r\n
\r\n Hi everyone, \n \nI am trying to pull this downgrade off, but after using my e3 card reader a couple of times it doesn\'t seem to save any of my files anymore. For example I am copying the e3downgrader fix BD beta.bin on to the e3 upgrader. This all works fine and I can see the file being on there, but when I unplug the device and plug it back in the .bin file is gone. Therefore when I want to put it in my ps3 it cannot read the file, because it is just not there! Can somebody please help me with this!? It used to work fine but all of the sudden I\'ve got this problem. \n \nGreetz KennynneK\r\n
\r\n Hi Guys, \n \nThis is my first time jb\'ing a Ps3. I have a slim cech 2001a 120gb on 4.x, already ordered the e3 flasher chip. \n \nQuestion:- we need to put the ps3 in factory service mode in one the steps of e3 flasher, can i use my nexus one as a usb factory service mode dongle, if yes, how? Thanks\r\n
\r\n hello \nim sitting currently on a dex->cex soft-brick. i tried to flash my nor back to cex but after i shutdown my ps3, brick! if i try to start it it beeps 5 times and then shutdown. \ni bought myself an e3cardreader and tried now several times to unbrick it, but it doesnt work. i put the e3downgrade 12.03.bin on my e3cr (led is shining blue) and then put it in my ps3 \n-power off ps3 \n-put dongle right usb slot \n-power on \n-start ps3 and press eject \n \nnow my problem is that the e3cr turns red, then blue but the ps3 beeps 5 times and then shutdown. like the brick. whats the problem. ive watched youtube videos and such and dont know why it doesnt work :/ i cant enter fsm -.-\r\n
hello \nim sitting currently on a dex->cex soft-brick. i tried to flash my nor back to cex but after i shutdown my ps3, brick! if i try to start it it beeps 5 times and then shutdown. \ni bought myself an e3cardreader and tried now several times to unbrick it, but it doesnt work. i put the e3downgrade 12.03.bin on my e3cr (led is shining blue) and then put it in my ps3 \n-power off ps3 \n-put dongle right usb slot \n-power on \n-start ps3 and press eject \n \nnow my problem is that the e3cr turns red, then blue but the ps3 beeps 5 times and then shutdown. like the brick. whats the problem. ive watched youtube videos and such and dont know why it doesnt work :/ i cant enter fsm -.-
\r\n \r\n
\r\n
\r\n
I\'m not exactly sure why it\'s doing that, but I know that I had the same problem, you not only need to have the e3 ready but you must also have the rogero 3.55 pup v3.4 or v3.7 works on the root of another regular USB thumb drive and also you need the lv2_diag.self file for entering factory service mode. (I don\'t have much time to write this at the moment so you\'ll have to find those files yourself) \n \n- power off the ps3 (switch/or unplug) \n- insert e3 (right slot) \n- power on \n- press power then eject \n- light goes blue, and you might still hear the siren beeps, it\'s ok \n- ps3 shuts off automatically \n- take out e3, insert regular usb in right slot with self file and PUP. \n- turn on regularly and it should be installing the cfw pup. \n \nThen it will either turn off or restart and you should be in FSM with CFW 3.55 CEX.\r\n
\r\n tried that and had all the files ready on an usbstick. withe3cardreader it still beeps and shuts down. if i insert the usb stick then, the ps3 starts, do beeps and shuts down again. no sign of any installing :/ \n \nEDIT:: \nhere ive made a video \n \nhttps://www.youtube.com/watch?v=IG4r...s&feature=plcp\r\n
\r\n
\r\n\r\n \r\n
\r\n
\r\n \r\n
\r\n \r\n \r\n
\r\n \r\n Last edited by dastimmy; 11-03-2012 at 11:42 AM.\r\n \r\n \r\n
tried that and had all the files ready on an usbstick. withe3cardreader it still beeps and shuts down. if i insert the usb stick then, the ps3 starts, do beeps and shuts down again. no sign of any installing :/ \n \nEDIT:: \nhere ive made a video \n \nhttps://www.youtube.com/watch?v=IG4r...s&feature=plcp
\r\n \r\n
\r\n
\r\n
\nFrom the video, it appears you are doing everything alright, so that means it\'s got to be either the files or the regular USB. Also, on your \nPC when you put the e3 card reader files on the dongle, you did put them in the upgrader part of the dongle and the light turned blue when you did that? I didn\'t get it on the first try, my PUP (I used Rogero\'s 3.55 v3.7) was ok, but I tried different .self files from different places. If I remember correctly it was the one from pepe\'s cex/dex guide here. Don\'t get defeated just yet, try different variations of files, if you are using Rogero\'s 3.55 v3.4 PUP, try version v3.7 you can download it at ps3scenefiles.com, you\'ll have to register to download from there. \n \nOne question, did you have to build a new nanddump from a DEX dump, or did you have your original Cex.Nanddump from before? And how did you flash that? Multiman? FSM?\r\n
From the video, it appears you are doing everything alright, so that means it\'s got to be either the files or the regular USB. Also, on your \nPC when you put the e3 card reader files on the dongle, you did put them in the upgrader part of the dongle and the light turned blue when you did that? I didn\'t get it on the first try, my PUP (I used Rogero\'s 3.55 v3.7) was ok, but I tried different .self files from different places. If I remember correctly it was the one from pepe\'s cex/dex guide here. Don\'t get defeated just yet, try different variations of files, if you are using Rogero\'s 3.55 v3.4 PUP, try version v3.7 you can download it at ps3scenefiles.com, you\'ll have to register to download from there. \n \nOne question, did you have to build a new nanddump from a DEX dump, or did you have your original Cex.Nanddump from before? And how did you flash that? Multiman? FSM?
\r\n \r\n
\r\n
\r\n
yeah the dongle falshes blue while upgraden. i tried different files. i download rogero3.7 later and try with it.but i think, its the dongle that just dont seem to work right -.- \n \ni flashed my original cex.nor with multiman and restartet then. brick! -.- but i hadnt used toggle_qa on cex. i think thats the reason of the brick.\r\n
yeah the dongle falshes blue while upgraden. i tried different files. i download rogero3.7 later and try with it.but i think, its the dongle that just dont seem to work right -.- \n \ni flashed my original cex.nor with multiman and restartet then. brick! -.- but i hadnt used toggle_qa on cex. i think thats the reason of the brick.
\r\n \r\n
\r\n
\r\n
I wish there was more help I could offer you. I think your E3 should be fine, maybe it\'s the regular thumb drive, maybe reformat? Use a different one? Just ideas, but hope you get it up and running, I wasn\'t too stoked about a bricked PS3 either.\r\n
\r\n ive found someone who had the same problem as me and got fixed it. but he wont answer my pm currently so maybe someone here knows how he fixed it \r\n \r\nhttp://www.ps3iso.com/ps3-help/17662...ex-cex-e3.html\r\n
\r\n\r\n \r\n 
\r\n \r\n 
\r\n 
\r\n \r\n \r\n \r\n 
Reply With Quote
\r\n \r\n 
Originally Posted by JLM\r\n 
\r\n 
Reply With Quote
